M. R. Mostofi Sarkari; M. S. Valiahdi; I. Ranjbar
Abstract
Grain loss monitors are installed on combine harvester and make it possible to measure grain loss on different parts of the combine. The instrument permits the operator to adjust a proper ground speed to keep grain loss within an acceptable range. In this study a loss monitoring system was implemented ...
Read More
Grain loss monitors are installed on combine harvester and make it possible to measure grain loss on different parts of the combine. The instrument permits the operator to adjust a proper ground speed to keep grain loss within an acceptable range. In this study a loss monitoring system was implemented to measure grain losses continuously on straw walker and sieves. Two grain loss monitors (KEE and TeeJet) were installed behind the straw walker and the sieves of JD-955 and JD-1165 combine harvesters. Harvesting performance parameters such as combine total and processing losses were then measured. To evaluate the precision and accuracy of the instruments, the measured and monitored losses were compared and investigated. The results of a two-year research showed that the average processing loss of the combine harvesters with 10-12% grain moisture content and 750 rpm drum speed was 0.82% which is whitin the acceptable range recommended by ASAE Standard No. S343.3. Furthermore, there was no significant difference between the measured and monitored values of processing loss.
J. Taghinazhad; M. R. Mostofi Sarkari
Abstract
Rapeseed cultivation in Iran is growing rapidly while this product has been facing specific problems. Every year a significant portion of edible oil is imported to the country from other countries. Despite this deficit, a great amount of canola is being lost every year. Therefore, in compliance with ...
Read More
Rapeseed cultivation in Iran is growing rapidly while this product has been facing specific problems. Every year a significant portion of edible oil is imported to the country from other countries. Despite this deficit, a great amount of canola is being lost every year. Therefore, in compliance with technical points, adding a suitable platform to the exisiting machineries may reduce the losses. A field study was conducted in Moghan Agricultural Research Centre to study the technical and economical characteristics of harvesting machineries and evaluate Canola harvesting losses in different maturity stages, using three different combine harvester heads. The experiments were conducted in a completely randomized split split plot design with four replications. The main plot included seed maturity stage at three levels: A) 60%, B) 70% and C) 80%, and the subplot was the harvester’s ground speed at three levels: A) 1.5, B) 2.5 and C) 3.5 km h-1. The sub-subplot was combine head type with three forms: A) Mechanical, B) Hydraulically Joybar and C) Hydraulically Biso's Head. The results of ANOVA showed that maximum cutter bar losses occurred with Mechanical Head (5.36%) while the loss of Hydraulically Joybar's and Biso's head were 4.28 and 4.13 %, respectively. The results also showed that the maximum cutter bar losses occurred when 80% of seeds were matured and adequate time for canola harvesting was 70% of seeds maturity. The results of analysing the effects of harvesting ground speeds showed that the maximum cutter bar losses occurred with the speed of 3.5 km h-1. Finally, the results showed that the minimum cutter bar loss was obtained with Hydraulically Joybar's head considering the benefit per cost ratio. The cost for Mechanical head and Hydraulically Biso's head were 13500 and 262500 Rial ha-1, respectively.
H. Ghorbanpour; M. H. Khoshtaghaza; M. R. Mostofi Sarkari
Abstract
Manual citrus harvesting is commonly performing hard, expensive and time consuming. In this study, a factorial experiment with a completely randomized design in three replications was performed to find out the effect of frequency (three levels of 5, 7.5 and 10 Hz), vibration time (three levels of 10, ...
Read More
Manual citrus harvesting is commonly performing hard, expensive and time consuming. In this study, a factorial experiment with a completely randomized design in three replications was performed to find out the effect of frequency (three levels of 5, 7.5 and 10 Hz), vibration time (three levels of 10, 15 and 20 seconds) on harvesting capacity and losses of Thomson cultivar of orange. The results indicated that the effect of frequency and vibration time was significant (P≤0.01) on the harvesting capacity and losses, but their interaction effects weren’t significant. The harvesting capacity significantly increased by increasing frequency, and the highest harvesting capacity was 62.8 % at 10 Hz frequency. Although the harvesting capacity increased by increasing the vibration time, but there was no significant difference in vibration times between 15 and 20 seconds at 10 Hz frequency. Also the fruit loss was increased by increasing the vibration time. Due to these reasons, frequency of 10 Hz and vibration time of 15 seconds were selected as the most suitable condition for mechanized harvesting of this cultivar of orange. Finally a linear mathematical model was developed based on the frequency and vibration time for the harvesting capacity and fruit loss of Thomson cultivar of orange.
M. R. Mostofi Sarkari
Abstract
Corn harvesting involves some losses. These losses result in decreased benefits. It is almost impossible to lower losses to zero percent but it can be controlled in an acceptable level. As a result of this research, appropriate methods are introduced to decrease losses and reduce waste. In this project, ...
Read More
Corn harvesting involves some losses. These losses result in decreased benefits. It is almost impossible to lower losses to zero percent but it can be controlled in an acceptable level. As a result of this research, appropriate methods are introduced to decrease losses and reduce waste. In this project, losses in different part of combine were measured and evaluated according to the available standard method (ASAE S396.2 & S343.3). Harvesting losses include preharvest and during harvest losses comprising ear loss and kernal loss in the header, cylinder and cleaning losses. This project was conducted on farmers’ lands in Gazvin province. Some assessments related to yield factors were evaluated in different parts of farm with specified area, e.g. Plant height, ear number, stem diameter, ear diameter, cob diameter, row/ear and seed/row. All losses evaluated in three treatments which they were: seed moisture content (w.b.) in three levels of 19%, 23% and 27%, ground speed in three levels of 0.8, 1.2 and 1.6 ms-1 and cylinder speed of 400, 600 and 800 rpm. The split plot experimental design based on the randomised complete block design (RCBD) was used to evaluate treatments. Measured losses compared with standard values to introduce the proper methods to decrease losses and proper adjustments. The results show that appropriate seed moisture content, cylinder and ground speed were 23%, 400 rpm and 1.2 ms-1, respectively. They had minimum total loss which WAS 1.55%, 2.65% and 2.34%, respectivily. The results also show that there was an ear loss in preharvest loss (because of bad weather condition) that was 0.95-5.42%, also kernal loss on the header and cylinder loss which all related to improper adjustment of combine but total loss was in an acceptable level and standard. It was variable from 1.55% to 4.02%. Other parameters such as using inexperienced driver, improper combine adjustment, and also nonuniformity of field and ear moisture content in different parts of field prevent using the outputs and recommendations of this research.
